How To Repair Rock Band Drum Pad
Rock Band 2 is a marked improvement over Stone Band – made largely perhaps past the inclusion of a killer wireless drum kit with a sturdier pedal and quieter pads. And the drum kit is made better by the improver of the cymbal expansion kit. Simply what if they break? What if they cease being responsive or don't offer the same performance as y'all would expect. Simple. Nosotros show y'all how to fix and repair them – stride by step – and using only basic tools yous are likely to already have lying around the house.
Rock Band 2 is a marked improvement over Rock Band – made largely possible past the inclusion of a killer wireless drum kit with a sturdier pedal and quieter pads. After a while, however, if y'all desire to keep playing you'll need to know how to fix Rock Band drums and cymbals. And the drum kit is made ameliorate by the addition of the cymbal expansion kit. But what if they interruption? What if they cease being responsive or don't offer the aforementioned functioning as you would expect? You could send them dorsum and risk getting another set that is worse or will break in an equally brusk amount of time. Depending on how long you've had them, you may actually be out of warranty. Whatever your scenario, nosotros'll show you how to gear up and repair them – pace by stride – and using only bones tools you are likely to already have lying around the house.
We're pretty sure this voids your warranty, merely we've washed it no less than two times and it's an extremely repeatable procedure that seems to prepare nigh problems users experience with their Rock Band cymbals. Be sure to check your warranty before you undertake any cymbal surgery…
The Trouble (Symptoms)
There are several potential problems that can arise with the Rock Ring 2 Cymbal Expansion Kit. These problems, fortunately, can be classified into two distinct scenarios:
ane) Loss of Responsiveness in a Rock Band ii Cymbal
The get-go problem involves a simple loss of resolution, where the cymbals will lose responsiveness over fourth dimension and cease to record each hit during songs. This, of course, is a major trouble as it causes dropouts from the game and prevents successful execution of a song. There's cypher worse than hitting the cymbal correctly and having it not record the note. The solution to this trouble lies within the sensor itself and nosotros'll show you how to brand information technology piece of work properly.
2) Complete Rock Band 2 Cymbal Failure
The second problem you can feel with these Rock Band expansion cymbals is a complete failure of the sensor which renders a cymbal useless. If this happens, don't sweat it – yous can probably "resurrect" your expansion cymbals with some quick, but easy, surgery.
Fixing Loss of Responsiveness in a Rock Band 2 Cymbal
While the Stone Band ii Cymbal Expansion Kit tin can add tons of new experiences to the Stone Ring experience, the cymbals seem to have some potential quality control issues depending on which batch you become. In whatever case, if the cymbals become unresponsive it is likely due to the positioning of the sensors located within the plastic housing. To fix the trouble, we take merely to disassemble the cymbal and readjust the sensor for proper alignment.
Stride 1: Case Disassembly
Lay the cymbal down on a flat working surface:
Grab a small Philips screwdriver and remove the center assembly which houses the electronics and sensor contained within the cymbal:
Pace 2: Sensor Identification
Underneath you will find the sensor lath (the sensor is underneath) and the small electronics board that handles ability and control of the signals. Don't panic—let your desire to play drive you lot to learn how to prepare Rock Band drums and cymbals. Y'all can make information technology!
Stride 3: Sensor Removal
What y'all desire to practise is elevator upwardly the sensor board and disassemble the sensor (yous'll replace it after):
Step 4: Sensor Realignment
Notation the position of the two metallic plates, they are virtually likely misaligned, with the pocket-size eye sensor beingness off-center from the superlative metal plate. What you want to practise is re-marshal the small metal pad to the center of the reddish backing area. This allows the cymbal to make consistent and positive contact each time it is struck and eliminates the root cause of misfires and erratic operation:
Step five: Replace the Sensor & Re-assemble the Cymbal
Later on yous realign the pads, supplant the sensor, being careful to guide the wires around the edge of the surface area where the plastic instance will be re-attached to the cymbal body. Replace the iv screws that hold the sensor in identify and supersede the plastic casing.
Pace 6: Replace and Examination
The only affair left to do is re-connect the cymbal and enjoy your new error-free Rock Band 2 Cymbal Expansion Kit!
Fixing a Completely Unresponsive Rock Ring 2 Cymbal
At times the problem with the Rock Band Expansion Cymbal Kit is a scrap more than astringent than mere misfires or erratic behavior. In some cases, the cymbal breaks entirely and stops sending signals to the drum kit. When this happens the solution is actually easier to fix than you lot might recall. To become your cymbal back in working order, you'll need a few household tools and you'll need to add a few more steps to the above remedy to score yourself a completely repaired cymbal.
Steps one-3: Instance Disassembly and Sensor Removal
Follow the steps above to disassemble the cymbal instance and inner plastic comprehend. Remove the sensor and examine all of the cabling. What you lot are looking for is a wire that has come loose from its solder connection. If you lot want to also check the alignment of the cymbal sensor, be sure to follow all steps above. One time you are prepare to fix the bad solder connection, go on on below:
Step 4: Identify the Bad Solder Connection and/or Broken Wire
In our feel, the bad solder connexion or cleaved wire is going to be located on the board connecting the control cablevision to the actual sensor. This involves one of vi total wires soldered to the lath. At this point you will also want to use a Sharpie or permanent mark to mark the wires and ensure that y'all reconnect them correctly to the board when you are finished:
Step 5: De-solder the Wire from the Board
When a single wire in a three-wire organisation is cleaved, you lot actually accept to de-solder all three wires in order to make a stable re-connection of the broken cable. In short, you accept to re-do all three. In order to accomplish this, use a soldering iron to de-solder one connectedness at a fourth dimension. De-soldering is tricky business organisation unless you have a solder-sucker. Without ane, you have to brand sure yous can pull out the cablevision while the solder is in its liquid form. It may take some trial and mistake, but eventually y'all'll have all 3 wires removed.
Pace six: Re-Strip and Re-Insert Wires
One time you take the wires all removed, re-strip them and apply the soldering iron to ensure that all three holes are still open and ready to accept the newly stripped wires. The triple greyness cablevision is where our bad connection was found and the wire is solid core and very thin. Y'all tin utilise a wire strippers for this, but to be honest, your fingernails or a small knife volition practise just as well. Once completed, insert the bare wires back through the iii holes as shown here:
Pace 7: Solder the Wires to the Board
Soldering isn't terribly difficult. Remember, it's not about getting the solder to cook – information technology's nearly getting the solder to menstruation. If the solder only liquefies you lot will end upward with a common cold solder joint and one that is likely to pause again in the virtually hereafter. To assure the solder is flowing, yous'll want to draw the solder through the connection past positioning the solder tip on the contrary side of where the solder is touching the wire and lath hole. This volition also ensure you don't use too much solder and short the connexion between the three wires. It helps to have someone hold the board while you solder – or to have three easily, whichever seems more practical to you. A practiced solder articulation volition look like it is clean and compatible:
Step 8: Trim Wires and Re-assemble the Cymbal
All that is left to do at this point is trim the wires and re-gather the cymbal for final testing.
Conclusion
That's all there is to it. After completing both of the repairs, nosotros confirmed that the cymbals were back to practiced working order and handed them over to the owner. He quickly reported that before, if a cymbal had loosened up on its stand up, information technology would not annals (or would double annals), now they practically had to autumn off the stand non to piece of work correctly. The owner of the cymbals described them every bit "Better than new." High praise indeed.
Fixing Stone Band 2 cymbals isn't as grueling procedure as y'all'd remember and it volition make a decidedly dramatic improvement on your playing should you be experiencing missed notes. Of course, if your cymbal is completely dead, then this fix is certain to get you dorsum up and rocking in no time – and save you the hassle and extra cost of having to re-buy new cymbals.
Enjoy!
Source: https://www.protoolreviews.com/news/repair-broken-rock-band-2-cymbals/3949/
Posted by: andersonbligh1975.blogspot.com
0 Response to "How To Repair Rock Band Drum Pad"
Post a Comment